· Terex Telelect Commander 6000 center mount derrick with 15,000 lb. turret winch and
transferable pole buddy for mounting over the rear axle
· Lift Capacities:
· Sheave Height: 60.6 ft.
· Load Radius: 49.8 ft.
· Fiberglass hydraulic third stage boom certified for rated line voltage up to and including 46
KVAC
· Dual lift cylinders, continuous rotation, self aligning swivel ball bushings, box fabricated
booms
· Command post with single stick control
· Allows one hand to operate three functions rotation, boom elevation and boom extension
· Other functions have individual controls
· Controls are full pressure, full flow hydraulic
· Mounted to the curb side of the turret
· Hydraulic foot throttle
· Glycerin-filled pressure gauge
· Two speed throttle control push button switch mounted near outrigger controls at rear
· 120 ft. of 1 in. of Samson Spectron II rope with swivel hook
· 12,000 ft. lb. two speed digger
· Planetary gear drive
· Air operated digger shift
· Air activated auger release
· 60 in. long x 2 5/8 in. hex auger shaft
· Digger hanger with transfer protection system
· Auger storage bracket, left side mounted
· Hydraulic latching auger catch with safety pin and auger roll-up cable
· Stores up to 24 in. auger in the standard position
· 60-0144 hydraulic shift for two-speed digger
· Digger storage protection protects auger storage cable from damage caused by over-winding
· Pengo 18 auger with 2 5/8 hex shaft and steel teeth
· Tilt pole plummer for transferable pole buddy
· Transfers from end of second section to end of third section
· Installed on transferable pole buddy flange assembly
· Hydraulic cylinders operate the tilt and open/close
· Holding valve for tilt pole plummer tilt cylinder
· 10-bolt PTO air shift for Allison MD3560 transmission.
· Hydraulic oil and lubricants
· Shut-off valve in suction line
· Top control package including the following components
· Insulated top controls for rotation, boom elevation and sequential extension of second
stage and insulated third stage: insulated third stage extends first and retracts last for
maximum insulation, Full pressure, full flow hydraulic controls with individual levers to allow
simultaneous and multiple boom functions
· 42 fiberglass platform, 24 x 24 x 42 inside/outside step with non-skid surface,
adjustable band brake and horizontal storage feature, safety belt and lanyard
· Insulated platform liner for 42 platform
· Vinyl platform cover for 24 x 24 platform
· Hydraulic tool power at platform
· Insulated engine throttle advance operable from the platform
· Auxiliary hydraulic tool power below rotation with control in outrigger valve bank
· Dripless quick couplers, 1 set
· Spring loaded hose reel with 25 ft. of hydraulic hose, RSC stop collars and quick couplers
· Hose reel mounted on top of platform at rear
· Two-part line attachment
· Muffler shield
· Super heavy-duty A-frame main outriggers
· 150 spread pin to pin and 166 to outside of pads
· 11 penetration based on 40 frame height
· 16 x 16 swivel pads
· Outrigger motion alarm
· Main outrigger controls at rear, one each side
· Extra heavy duty A-frame auxiliary outriggers
· 150 spread pin to pin and 166 to outside of pads
· 11 in penetration based on 40 frame height
· 16 x 16 swivel pads
· Outrigger motion alarm
· Auxiliary outrigger controls for remote location
· Subframe weldment and tie-down kit for 138 CT
· Command post steps
· Terex Telelect T-40 heavy duty transverse through compartment body installed behind the
cab, 40L x 48H x 92W
· Constructed of A-60 (iron zinc) alloy metal
· Double panel doors with paddle handle locks
· Stainless steel pin piano hinges
· Compartmentation
· Curbside Two 6 drawers with adjustable dividers. One 4 drawer with adjustable dividers
· Friction slides
· Rear portion of compartment contains 36 tool board with tool bit holder, tool storage, J
hooks and straight hooks
· Streetside 40 vertical compartment with four (4) J hooks
· Telelect East Standard Heavy Duty 14’ treadplate platform
· Recessed platform access steps installed behind T-40-01, curbside
· 3 lip around platform to retain loose material
· 24 platform
· Four (4) outrigger pad racks to hold two (2) 24 x 24 pads, one each side, under saddlebox
· Four (4) 24 x 24 outrigger pads
· Wheel chock storage between the tandem, one each side
· Two (2) rubber wheel chocks installed in holders
· ICC rear bumper
· Frame mount derrick rest
· Two grab handles at rear
· DOT FMVSS lighting package
· Mud flap assembly
· Install 50’ of useable grounding cable including three point grounding of unit, chassis and
body with hot
· line clamp on one end. Install storage bracket on rear of compartment’s right side to store
cable. 1/0
· Multi-strand copper cable.
· 20,000 lb. pintle hook complete with crossmember brace and two safety chain D rings
· 6-way trailer socket installed at rear
· Terex Telelect pole puller with 8x12 base plate and chain
· Pole puller storage rack installed on front outriggers, curbside
· Preco amber strobe light with switch in cab, mounted on boom support. Brush guard
· Rubber dock bumpers at rear (pair)
· DOT inspection
· 10 lb. fire extinguisher with mount bracket
· Triangle reflector kit with storage box
· Install PTO hour meter
· Paint digger derrick, T-40-01 and platform body White. Paint T-40-01 interior gray with
speckled white paint
· Install customer-supplied Compass door decals, dealer-supplied DOT numbers and
Compass unit numbers
